-
Recent Posts
Equipment Manufacturers
Archives
- November 2021
- October 2021
- September 2021
- August 2021
- July 2021
- June 2021
- May 2021
- April 2021
- March 2021
- February 2021
- January 2021
- December 2020
- November 2020
- October 2020
- September 2020
- August 2020
- July 2020
- June 2020
- May 2020
- March 2020
- May 2019
- April 2019
- March 2019
- February 2019
- January 2019
- December 2018
- November 2018
- October 2018
- September 2018
- August 2018
- June 2018
- May 2018
- April 2018
- March 2018
- February 2018
- January 2018
- December 2017
- November 2017
- October 2017
- September 2017
- August 2017
- July 2017
- May 2017
- April 2017
- March 2017
- February 2017
- January 2017
- December 2016
- November 2016
- October 2016
- August 2016
- July 2016
- June 2016
- April 2016
- March 2016
- February 2016
- January 2016
- December 2015
- November 2015
- October 2015
- September 2015
- August 2015
- July 2015
- May 2015
- April 2015
- March 2015
- February 2015
- January 2015
- December 2014
- November 2014
- October 2014
- July 2014
- June 2014
- April 2014
- February 2014
- January 2014
- December 2013
- November 2013
- October 2013
- September 2013
- August 2013
- July 2013
- May 2013
- February 2013
- January 2013
- December 2012
- November 2012
- September 2012
- August 2012
- May 2012
- April 2012
- March 2012
- October 2011
- September 2011
Categories
-
Monthly Archives: August 2013
2013-08 Firewall – Finish
Today I fiished up the placement of the firewall. I cut the fiberfrax to size and used sprayglue to stick it neatly to the back of the composite engine firewall. It stuck real good and then was covered by the … Continue reading
Posted in Engines, Fuselage
Leave a comment
2013-08 Rudder Pedal Conduit
I decided that the rudder conduits as they were installed by the former owner, would bind at the bottom near the rudder pedals when they were moving aft. The line was laying flat against the ducts, and it would have … Continue reading
Posted in Flight Controls, Fuselage
Leave a comment
2013-08 Static Ports installation.
For the installation of the static port, I am deviating from the manual. I found a pair of nice ports in the Aircraft Spruce catalog, especially for composite aircraft. Easy to install, drill a hole, Fill up with epoxy filler … Continue reading
Posted in Avionics, Fuselage
Leave a comment
2013-08 Electrical Schematic
Since I do not have much time off this week, I decided to sit behind the computer an draw my schematic in the Edraw software that I bought specifically for this job. This is one example of what it looks … Continue reading
Posted in Electrical System
Leave a comment
2013-08 Overhead Lights installed.
I worked on getting the first lights installed into the overhead channel. Those lights are for the forward seats. They are shining from just behind the seats into the laps of the pilot and fwd pax seat. The next two … Continue reading
Posted in Electrical System, Fuselage
Leave a comment
2013-08 Preplanning the Flip..
Today I put on the ears onto the airplane.. EARS you say ? Yes, They look to me like big floppy elephant ears. But they have a reason to be attached. Soon the aircraft will have to be upside down. … Continue reading
Posted in Fuselage
Leave a comment
2013-08 Sparrow Strainer
One of the easy and quick thing to put together is the Sparrow Strainer. This little wing shape is connected to the Elevator and helps build a feel when you pitch the elevator. The parts were drawn out on a … Continue reading
Posted in Flight Controls
Leave a comment
2013-08 Firewall (cont.)
Well a week later and I am still cutting the firewall. My Dremel is making overtime. I use a diamond cutter, but unfortunately the aluminum screw holding the cutter attached, gets hold and broke off.. 4 times. I ran out … Continue reading
Posted in Engines
Leave a comment
2013-08 Firewall
Yesterday evening I started to make a template of my firewall. It will not be long before the firewall can be installed, as well as the engine. Before that happens though we need to cut the firewall out of a … Continue reading
Posted in Building, Engines, Fuselage
Leave a comment
2013-08 Headset plug covers
In planning ahead for the electrical schematic and layout, I wondered where I should plug in the headsets. We will have 4 headsets, one in each position, two on the back bench and two up front for each seat. I … Continue reading
Posted in Avionics, Electrical System, Fuselage
Leave a comment