-
Recent Posts
Equipment Manufacturers
Archives
- November 2021
- October 2021
- September 2021
- August 2021
- July 2021
- June 2021
- May 2021
- April 2021
- March 2021
- February 2021
- January 2021
- December 2020
- November 2020
- October 2020
- September 2020
- August 2020
- July 2020
- June 2020
- May 2020
- March 2020
- May 2019
- April 2019
- March 2019
- February 2019
- January 2019
- December 2018
- November 2018
- October 2018
- September 2018
- August 2018
- June 2018
- May 2018
- April 2018
- March 2018
- February 2018
- January 2018
- December 2017
- November 2017
- October 2017
- September 2017
- August 2017
- July 2017
- May 2017
- April 2017
- March 2017
- February 2017
- January 2017
- December 2016
- November 2016
- October 2016
- August 2016
- July 2016
- June 2016
- April 2016
- March 2016
- February 2016
- January 2016
- December 2015
- November 2015
- October 2015
- September 2015
- August 2015
- July 2015
- May 2015
- April 2015
- March 2015
- February 2015
- January 2015
- December 2014
- November 2014
- October 2014
- July 2014
- June 2014
- April 2014
- February 2014
- January 2014
- December 2013
- November 2013
- October 2013
- September 2013
- August 2013
- July 2013
- May 2013
- February 2013
- January 2013
- December 2012
- November 2012
- September 2012
- August 2012
- May 2012
- April 2012
- March 2012
- October 2011
- September 2011
Categories
-
Monthly Archives: July 2017
2017-07 Side Stick and Armrests.
I finished up the final setup for the side sticks. They clear the armrests, and it is now time to send the doors back to JD’s Upholstery. It is time to finish the side panels with upholstery. My son got … Continue reading
Posted in Building, Flight Controls, Fuselage
Leave a comment
2017-07 Planning Mixture cable attachment point.
Underneath the engine is the fuel servo with three handles, one of which is the Mixture Control. With the new setup for clearing the cowling, I had to come up with a new bracket to operate the Mixture handle. I … Continue reading
Posted in Building, Engines
Leave a comment
2017-07 NAV and STROBE LIGHTS Tested – OK !
Now that the wings are on, I can test the complete wiring for the Strobes and the Navigation Lights. I hooked up all the connectors and tested all lights. Ops checks Good !
Posted in Building, Electrical System, Finishing, Wings & Canard
Leave a comment
2017-07 Engine Air Scoop adjustment.
Now that the engine cowling is installed, I decided to cut the lip off the engine air scoop and even cut the sides back to approximately the right size. I removed the aft scoop from the wooden board and cut … Continue reading
Posted in Uncategorized
Leave a comment
2017-07 Engine Cowling cut around wings.
Now that the wings are on, I can do so much work again. One of the things we right away had marked, was cutting the top dan bottom engine cowlings. The wings fit inside the cowling, and holes need to … Continue reading
Posted in Building, Finishing, Fuselage
Leave a comment
2017-06 Wings attached !
Today, for the first time since the airplane build has started, we were able to get to the point that we could get both wings on, at the same time, and make it look like a real Velocity. It took … Continue reading
Posted in Building, Finishing, Wings & Canard
Leave a comment