-
Recent Posts
Equipment Manufacturers
Archives
- November 2021
- October 2021
- September 2021
- August 2021
- July 2021
- June 2021
- May 2021
- April 2021
- March 2021
- February 2021
- January 2021
- December 2020
- November 2020
- October 2020
- September 2020
- August 2020
- July 2020
- June 2020
- May 2020
- March 2020
- May 2019
- April 2019
- March 2019
- February 2019
- January 2019
- December 2018
- November 2018
- October 2018
- September 2018
- August 2018
- June 2018
- May 2018
- April 2018
- March 2018
- February 2018
- January 2018
- December 2017
- November 2017
- October 2017
- September 2017
- August 2017
- July 2017
- May 2017
- April 2017
- March 2017
- February 2017
- January 2017
- December 2016
- November 2016
- October 2016
- August 2016
- July 2016
- June 2016
- April 2016
- March 2016
- February 2016
- January 2016
- December 2015
- November 2015
- October 2015
- September 2015
- August 2015
- July 2015
- May 2015
- April 2015
- March 2015
- February 2015
- January 2015
- December 2014
- November 2014
- October 2014
- July 2014
- June 2014
- April 2014
- February 2014
- January 2014
- December 2013
- November 2013
- October 2013
- September 2013
- August 2013
- July 2013
- May 2013
- February 2013
- January 2013
- December 2012
- November 2012
- September 2012
- August 2012
- May 2012
- April 2012
- March 2012
- October 2011
- September 2011
Categories
-
Category Archives: Accesories
2021-10-29. Maintenance.
Two days after my failed turbo test, I came back to the hangar and once again removed the cowling. I first thought to remove the top only, but then decided to take both off. I double checked the throttle arm … Continue reading
Posted in Accesories, Engines
Leave a comment
2021-03 Finishing work – runup, brakes
Starting this day a little early and install the back seat and aft cabin wall in anticipation of weighing the aircraft. We also installed the frontseats and Howard put most of the remaining labels we require, on the flight and … Continue reading
Posted in Accesories, Engines, Finishing, Wings & Canard
Leave a comment
2021-01 Finishing work
Howard Kohnstamm and I had a busy day making the sqauwklist shorter. We started out with the main landing gears adding the AN6-35 bolts and torqued all nuts. The left main bearings were already greased, but the right side main … Continue reading
Posted in Accesories, Avionics, Building, Electrical System, Finishing
Leave a comment
2020-10 Towbar tryout.
I finally found the towbar that fits a Velocity FG nosewheel fork setup. It is actually build for an RV-10, and it fits well although the nosewheel wheelpant is bulkier and makes the towbar stand up under a 45 degree. … Continue reading
Posted in Accesories
Leave a comment
2018-12 OIL problems – AGAIN !
Today I entered the hangar to find a lot of the Turbo oil on the floor, dripping out the exhaust – AGAIN .. This is becoming frustrating. We thought we solved the problem by adding the suction pump. We did … Continue reading
Posted in Accesories, Engines
Leave a comment
2018-11 Oil QTY Tank Hose replaced
When Bas and I were doing some testing, we had removed temporarily the exhaust to check for draining oil out of the turbo. Apparently, the airflow during subsequent engine run was such, that heat ended up on the RH top … Continue reading
Posted in Accesories, Engines
Leave a comment
2018-11 New Turbo ON switch
The switch part of the Turbo ON-lighted switch unit has been problematic. It never really served the way I envisioned. That meant we had to find a new switch that would work correctly. I finally found some time and sat … Continue reading
Posted in Accesories, Electrical System
Leave a comment
2018-05. Ram air vents
Today I ran the hoses for the ram air vents. I had those hoses already precut, but I had waited to find a aluminum tube to connect two hoses easily together and yet be able to quick disconnect them when … Continue reading
Posted in Accesories, Building, Finishing, Instrument Panel
Leave a comment
2018-02 Running VIRB360 wiring
I removed the overhead channel for other reasons, but while working on that, I decided I could drill a hole underneath the camera attachment bracket, and feed the wiring to behind the vanity panels. I drilled the hole, just big … Continue reading
Posted in Accesories, Building
Leave a comment